-
T/CWAN 0099-2023 液化天然气用奥氏体不锈钢管焊接工艺规程
本文件规定了气体运输船液化天然气用奥氏体不锈钢管焊接的一般要求、工艺要求、检验、返修、
焊后处理、安全防护等内容。
本文件适用于外径≥11mm的、壁厚2.1 mm~16 mm范围内的气体运输船液化天然气用奥氏体不锈钢
管焊接。...2024-02-27 22:30:01浏览:5
查看 -
JB/T 12625-2016 液化天然气用球阀 Ball valves for liquefied natural gas
本标准规定了液化天然气用球阀的结构型式, 技术要求, 检验、 试验方法, 检验规则, 标志, 防护、包装和储运。
本标准适用于公称压力PN16~PN250、 公称尺寸DN 15~DN700和压力等级C1ass150~C1ass1500、公称尺寸NPS1/2~NPS28, 工作介质为液化天然气的法兰和焊接连接球阀(以下简称球阀)。 其他温度高于-162℃的低温球阀亦可参照使用。...2024-01-30 00:15:02浏览:9
查看 -
SY/T 7683-2023 液化天然气带压密封技术规范
本文件规定了液化天然气管道、法兰、阀门泄漏带压密封作业准备、实施、验收的程序。
本文件适用于压力 8MPa(表压) 及其以下的液化天然气泄漏的带压密封作业,其他低温介质带压密封作业参照使用。...2024-01-12 01:24:01浏览:7
查看 -
ISO 12614-16-2021 公路车辆--液化天然气(LNG)燃油系统组件--第16部分:热交换器--蒸发器 Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 16: Heat exchanger-vaporizer
This document specifies tests and requirements for the heat exchanger-vaporizer, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following:<br />a) fuel containers;<br />b) stationary gas engines;<br />c) container mounting hardware;<br />d) electronic fuel management;<br />e) refuelling receptacles....
2024-01-04 14:12:30浏览:9
查看 -
ISO 21903-2020 冷冻烃流体--动态测量--液化天然气(LNG)和其他冷冻烃流体用流量计的校准和安装要求和指南 Refrigerated hydrocarbon fluids — Dynamic measurement — Requirements and guidelines for the calibration and installatio
This document specifies the metrological and technical requirements for flowmeters intended to be<br />used for the dynamic measurement of liquefied natural gas (LNG) and other refrigerated hydrocarbon fluids. For LNG static volume measurement used in custody transfer, see ISO 10976.<br />This document sets the best practice for the proper selection and installation of flowmeters in cryogenic applications and identifies the specific issues that can affect the performance of the flowmeter in use.<br />Moreover, it offers a calibration guideline for laboratory and on-site conditions (mass or volume) by<br />either using LNG or other reference fluids. The choice of calibration fluid will depend on the capabilities of the available flow calibration facilities and the ability to achieve the required overall measurement uncertainty demanded by the intended application.<br />This document is applicable, but is not limited, to the use of Coriolis and ultrasonic flowmeters for<br />dynamic measurements of LNG.<br />In principle, LNG and other refrigerated liquid hydrocarbons are considered in this document.<br />Recommendations in this document are based on the available test results with LNG. These results are probably applicable to other cryogenic fluids....
2023-12-21 18:24:01浏览:13
查看 -
ISO 12614-7-2021 公路车辆--液化天然气(LNG)燃油系统组件--第7部分:压力释放阀 Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 7: Pressure relief valve (PRV)
This document specifies tests and requirements for the pressure relief valve (PRV), a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following:<br />a) fuel containers;<br />b) stationary gas engines;<br />c) container mounting hardware;<br />d) electronic fuel management;<br />e) refuelling receptacles....
2023-12-17 09:00:01浏览:8
查看 -
GB/T 42864-2023 正式版 液化天然气的取样设施及取样性能检验
GB∕T 42864-2023 正式版 液化天然气的取样设施及取样性能检验...
2023-11-02 07:36:02浏览:11
查看 -
ISO 12614-1-2021 公路车辆--液化天然气(LNG)燃油系统组件--第1部分:一般要求和定义 Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 1: General requirements and definitions
This document specifies general requirements and definitions of liquefied natural gas fuel system components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking....
2023-10-29 08:48:01浏览:8
查看 -
YB/T 4641-2018 液化天然气储罐用低温钢筋 Cryogenic ribbed bars for the reinforced concrete tanks of LNG
本标准规定了液化天然气(LNG)储罐用钢筋的定义、牌号、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志和质量证明书等。<br />本标准适用于制造液化天然气储罐用直径不大于50mm的低温钢筋(以下简称钢筋)。...
2023-10-13 02:24:01浏览:23
查看 -
JJF(浙) 1197-2023 液化天然气立式储罐容量校准规范
本规范适用于液化天然气立式储罐容量的校准,其他类似结构的立式储罐
容量校准可参考本规范。...2023-09-22 05:12:01浏览:12
查看 -
GB/T 39248-2020 输送液化石油气和液化天然气用热塑性塑料多层(非硫化)软管及软管组合件 规范 含2023年第1号修改单
本标准规定了2种型别的输送液化石油气和液化天然气用热塑性塑料多层(非硫化)软管及软管组合件的要求。
每种型别分为2类一类是用于岸上另一类是用于离岸:
——A类用于岸上;
———B类用于离岸。
本标准适用于内径为25 mm~300 mm工作压力为1.05 MPa~2.5 MPa和工作温度范围为一196 ℃~+45℃的热塑性塑料多层(非硫化)软管及软管组合件。
注:离岸液化天然气软管组合件在 EN 1472-2中也有规定。...2023-08-07 00:36:01浏览:21
查看 -
GB/T 41319-2022 液化天然气(LNG)加液装置 Liquefied natural gas(LNG) fueling installations
本文件规定了液化天然气(LNG)加液装置的分类、代号和型号、结构和材料、要求、试验方法、检验规则、质量证明文件、标志、包装和运输。<br />本文件适用于在城镇液化天然气供应站、汽车加气站等场站内使用的液化天然气(LNG)加液装置(以下简称“加液装置”)。<br />城镇液化天然气供应站内使用的液化天然气(LNG)装卸装置可参照执行。...
2023-06-13 13:24:01浏览:24
查看 -
Q/SY 05678-2019 液化天然气接收站装船规程
本标准规定了液化天然气接收站装船作业的基本要求及作业步骤等内容。
本标准适用于液化天然气接收站的装船作业。...2023-06-01 12:00:01浏览:28
查看 -
GB/T 37770.1-2022冷冻轻烃流体 自动液位计的一般要求 第1部分: 海上浮式储存液化天然气自动液位计Refrigerated light hydrocarbon fluids-General requirements for automatic tank gauges-Part 1 : Automatic tank gauges for liquefied natural gas marine floating storage
本文件规定了用于液化天然气(LNG)海上运输船或浮式储存贸易交接计量用自动液位计(ATG)的安全注意事项、设计、安装、准确度、校准与验证、校准记录等的一般要求。<br />本文件适用于完全冷藏(即在低温条件下)或部分冷藏且压力等于或者接近大气压的LNG储罐用ATG,不适用于加压储罐用ATG。...
2023-04-15 16:20:02浏览:33
查看